氣源處理器使用的注意事項氣動電磁閥廠

氣源處理器使用的注意事項

Cautions in Application of F.R.L Equipment

一、安裝注意事項:(cautions in installation)

 ●氧氣源工作器按照時過慮器、過慮釋放壓力閥、油霧器不得不鉛垂按照，保溫水杯向右,釋放壓力閥調壓旋紐向右,且汽體傳遞目標中心點不得不按泵殼上下箭頭下圖目標中心點。

 ●安裝時請考慮一定的安裝與維護空間(如過濾器的安裝高度以能卸下水杯為準),氣源處理器避免安裝在有較強振動的環境中,以維護壓力表精度及連接件強度。

●做到應對裝配在強光爆曬的場景。

●Clean the pipes before installation of pneumatic components  associated，Remove dust、oil、debris、etc.to prevent the fragments of sealing material mix。

●When installed，  the filter、filter regulator and lubricator must be vertically, the cup down, the knob of regulator down, and the gas flow direction must be consistent with the arrow on valve body。

●Before installation, please set some space for installation and maintenance (such as the height of filters mounting ，to be able to remove the cup)。FRL should be avoid installed in a strong vibration environment ，to protect the accuracy of pressure gauge and the strength of the connection。

●Avoid to installation in sunshine point-blank  occasion。

二、使用時注意事項:(Cautions in usage)方向控制閥廠家

●進行脫水皿應定存刷洗濾清器，不然經進行脫水皿后體統負壓降早已變大。濾清器與喝水杯請你家中用中性粒細胞刷洗劑刷洗，接下來用自來水漂凈。

●請表明應用場景隨和壓系統標準選定合適的過濾程序器程度及排水的原則。

●塑料水杯與油杯質量為聚碳酸，應杜絕與四氯化碳、酸類、堿類、苯胺、打火機油和其他對聚碳酸脂起有機化學物質發生反應的有機化學物質貨品。

●填寫過濾程序裝置器及過濾程序裝置減壓方法閥茶杯或茶杯護罩準確佳后，足以關掉學習壓力，在負壓程序下一定要避免旋轉視頻茶杯簡答護罩 。

●過濾減壓閥（W型）、減壓閥（R型）使用時將調壓旋鈕拔出調至使用壓力，調完后將調壓旋鈕推入（止旋）。根據使用情況選擇相應的壓力表，方型壓力表和單向閥板組件可以進行互換。

●油霧器可在停不下來氣事情下捧場。請將油杯內油表保持良好在油表受限制與底限標準內。L3000、L4000旋開注油塞，從注油塞口處捧場。L1000、L2000將進氣塞旋開，確診穩定度空氣，拆卸塑料杯子會直接從杯口捧場；再將油杯旋入閥體，再將進氣塞卡緊。(油霧器運行ISO VG32或同級防銹液油)

●油霧器滴液的聯通流量數據的調控，用一個字型調控工服逆時針調控調油件滴液的聯通流量數據提高，順時鐘調控調油件滴液的聯通流量數據縮減，調控操作過程中不能夠用點力過大。

 ●殘壓排清去:排清去玻璃杯內的壓強(F.W用放水旋塞、L1000、2000系用res排氣閥門管塞res排氣閥門管、L3000、4000  系用注油塞res排氣閥門管）后，請驗證壓強是否是仍然檢測。

 ●汽源凈化cpu中密封圈適用期限3-5年，適用過期請確定更新。

●The filter should be cleaned regularly, otherwise the system pressure drop will increase. When cleaning the filter or the cup, use a neutral household detergent, then rinse with water.

●According to the work environment and the requirements of pneumatic system to select the appropriate filter such as size or drainage patterns。

●As the cup is made of polycarbonate, should avoid contact with carbon tetrachloride, acids, bases, aniline, kerosene and other chemicals be easy to reaction with polycarbonate.

●Before the open,make sure the cup or cup shield of the filter and filter regulator in right place。 Under the pressure, do not rotate the cup or shield.

●When using, please pull out the regulator knob such as filter regulator (W type) or regulator (R type), Adjusted to the desired pressure，Then push the regulator knob to prevent rotation. According to select the appropriate use of pressure gauge. Square gauge and check valve plate assembly can be interchanged.

●Please maintain the oil in the cup in the upper and lower limits. You can add oil in the case non-stop gas 。

1 for the L3000, L4000 series, first unscrew the fill plug, and add oil through the fill plug hole.

2 for L1000, L2000 series, first unscrew the vent plug, then remove the cup, add the oil directly to the cup; then screwed the cup into the valve, then tighten the vent plug. (Lubricator with oil ISO VG32 or Same level )

●Lubricator drip flow regulation: we can use a screwdriver to adjust the regulator. Counterclockwise, drip flow increases; clockwise, drip flow reduction. Note: The adjustment process can not be too hard.

●Discharge of residual pressure:The pressure within the exhaust cup (FW with drain cocks, L1000、2000 series with the exhaust vent plug, L3000、4000 series with the fill plug exhaust), make sure the pressure is completely ruled out.

●The normal life of the product seal is five years, to be replaced periodically.